
Florida Fire Protection Contractor III: Requirements and Scope
What the Florida Contractor III license covers (carbon dioxide, foam, dry chemical, Halon and other chemical systems), the experience you need to sit the exam, fees and renewal.
Contents
Florida Fire Protection Contractor III: Requirements and Scope
Contractor III is Florida's chemical-systems contractor license: the engineered special-hazard work that sits outside water-based fire protection. If you install carbon dioxide, clean agent or engineered dry chemical systems, this is the class that covers your scope without asking you to sit for sprinklers.
This guide covers what Contractor III authorizes, how it differs from the pre-engineered license people often confuse it with, and what you need before you can sit the exam.
What Contractor III authorizes
Under F.S. § 633.102, a Contractor III's business is limited to contracts that require the ability to fabricate, install, inspect, alter, repair and service:
- Carbon dioxide systems
- Foam extinguishing systems
- Dry chemical systems
- Halon and other chemical systems
Pre-engineered systems are excluded. That exclusion matters more for Contractor III than for any other class, because so much chemical-agent work in the field is pre-engineered.
Contractor III is not the pre-engineered license
Pre-engineered kitchen hood, dry chemical and clean agent systems are licensed separately in Florida, through the fire equipment dealer Class D license and the pre-engineered permit under F.S. § 633.304. Those are different exams with different rules. We cover them in the Florida pre-engineered systems license guide.
F.S. § 633.102 defines a pre-engineered system as one designed to protect specific hazards and installed within pretested limitations and configurations specified by the manufacturer, using the manufacturer's specified or listed-equal components. Chemical systems outside that definition are Contractor III (or Contractor I) work.
Contractor III in the I–V family
| Class | Scope | Exam |
|---|---|---|
| Contractor I | Every fire protection system type except pre-engineered | 100 questions, 150 minutes |
| Contractor II | Water-based systems | 100 questions, 150 minutes |
| Contractor III | Carbon dioxide, foam, dry chemical, Halon and other chemical systems | 100 questions, 150 minutes |
| Contractor IV | NFPA 13D sprinklers in detached one- and two-family dwellings and mobile homes | 50 questions, 60 minutes |
| Contractor V | Underground fire mains, from the point of service to 1 foot above the finished floor | 100 questions, 150 minutes |
Contractor I covers everything Contractor III does, plus all water-based work. If your business does both, Contractor I is the single license that covers it.
Eligibility
Under F.S. § 633.318(3)(d), to sit the Contractor III examination you must:
- Be at least 18 years old
- Be of good moral character
- Have 4 years of verifiable employment experience with a fire protection system as a Contractor I or Contractor II, or an equivalent combination of education and experience in chemical fire suppression systems
The statute adds that required education and experience for Contractors I through IV includes training and experience in both installation and system layout.
Once approved, your exam authorization is valid for six months.
Fees
| Item | Fee |
|---|---|
| Application | $300 per class of certificate |
| Biennial renewal | $150 per class of certificate |
The Pearson VUE candidate handbook lists no charge at reservation for the Contractor I–V exams, while F.S. § 633.132 lists a $100 examination or reexamination fee for each class. Confirm the current figure with the Bureau when you apply.
Renewal and reciprocity
Certificates expire every two years at midnight on June 30. Under F.S. § 633.332, a Contractor III certificate cannot be renewed without at least 32 contact hours of continuing education in the fire protection discipline during the biennial period.
F.S. § 633.318 contains no reciprocity provision. Out-of-state experience may support your eligibility, but the Florida exam is not waived.
The exam you are working toward
The Contractor III exam is 100 questions in 150 minutes, 70% to pass, open book, at Pearson VUE. Expect one surprise in the outline: the single heaviest standard on this chemical-systems exam is NFPA 25, the water-based inspection, testing and maintenance standard, at 22%.
The full weighting is in what's on the Contractor III exam, and the thirteen permitted references are in the Contractor III exam-day guide.
What to do next
Confirm your four years of chemical-systems experience is documented, layout included, and get your application in.
Our Florida Fire Protection System Contractor practice tests include a Contractor III exam weighted to its own Pearson VUE outline, and one subscription covers all five classes. Every answer cites the NFPA standard or Florida rule section behind it.
Try the free 10-question sample test first.
Scope, eligibility, fee and renewal details come from F.S. §§ 633.102, 633.132, 633.318 and 633.332, and the Florida Fire Prevention candidate handbook. Confirm current requirements and fees with the Bureau of Fire Prevention before applying. This is exam-prep guidance, not legal advice.
Ready to pass Florida Fire Protection System Contractor (I–V)?
Start your prep with unlimited practice tests and codebook-referenced answers.
Start Studying →

