
What's on the CSA PEG2 Clean Agent Exam: NFPA 2001, NFPA 72, the NEC and Voltage Drop
The books and editions for CSA's PEG2 Pre-Engineered Gas Clean Agent On-Site exam, what the NFPA 2001, NFPA 72 and NEC questions cover, a worked voltage-drop example using CSA's method, and a study plan.
Contents
What's on the CSA PEG2 Clean Agent Exam
CSA's PEG2 Pre-Engineered Gas Clean Agent On-Site exam is 80 questions in 120 minutes, open book, with an 80% pass mark. It covers more than the agent. In CSA's words it includes "control panels, wiring, notification, detection, agent criteria, enclosure design, and much more", because a clean agent system is released and supervised by a fire alarm panel.
CSA publishes no topic weights. Its study guide (dated January 19, 2022) gives sample questions and a list of NFPA 72 topics. This article works from those.
The books, and the editions CSA tests
| Book | Edition CSA lists | Allowed in the room? |
|---|---|---|
| NFPA 2001, Clean Agent Fire Extinguishing Systems | 2018 | Yes |
| NFPA 72, National Fire Alarm and Signaling Code | 2019 (handbook recommended) | Yes |
| NFPA 70, National Electrical Code | Any edition from 2008 to 2020 | Yes |
| International Building Code | Not specified | Yes |
| CSA PEG2 study guide | January 2022 | Yes |
| OSHA lockout/tagout, fall protection, PPE | n/a | No |
For the NEC, CSA has checked that every edition from 2008 to 2020 gives the same answers to its questions, so use the one you own. The OSHA material is different: the guide warns of "a few questions" on lockout/tagout, fall protection, hard hats and other safety gear, and you can't bring it in.
A note on our practice questions. Our PEG2 practice exam is written on exactly the editions CSA lists: NFPA 2001 (2018), NFPA 72 (2019) and the 2020 NEC, plus the OSHA safety material.
How the questions are labeled
Most questions name their source in brackets, such as [NFPA 72] or [NFPA 2001]. General questions on wire size or basic science carry no label. Questions can come from the body of NFPA 2001 and its annexes.
NFPA 2001: the agent and the system
CSA's important concepts for PEG2 are enclosure integrity, agent selection for the hazard, concentration versus time, local application versus total flooding, and definitions. The sample questions add:
- definitions such as listed, Class A fire and design factor;
- where agent containers and accessories must be located;
- the pressure-vessel standards containers must meet, depending on whether they are also used for shipping;
- container storage temperature limits;
- what must appear on flow calculation printouts submitted with working plans;
- the design factor table for piping tees;
- dividing a series of interexposed hazards into smaller groups; and
- what sets the agent quantity for a local application system.
CSA says it does not test manufacturer listings or system limitations. Those come from manufacturer training.
NFPA 72 and the NEC: the panel and the wiring
The study guide lists these NFPA 72 and NEC topics "to make sure you have studied this material":
- how many addressable devices a single fault may take out;
- strobe spacing and candela for wall and ceiling mounting, and ADA rules for strobes in public and common-use areas;
- pathway survivability classes;
- wire types, ratings and limits, and NEC Articles 110, 300 and 760;
- spacing for heat, smoke and duct detectors, flow switches and pull stations;
- measuring air velocity and pressure at duct detectors, and the equipment used;
- inspection, testing and maintenance frequencies; and
- documents owed to the owner, such as the record of completion.
Voltage drop: CSA's method
CSA's guide works a voltage-drop problem step by step, and its own instructions say to bring a calculator "for voltage drop calculations". The method uses Ohm's law, V = IR: voltage drop equals current times wire resistance. Here it is with our own numbers.
The circuit: six strobes on a 24-volt notification circuit. Their currents are 0.110, 0.110, 0.140, 0.180, 0.180 and 0.180 amps. The last strobe is 350 feet of conduit from the panel. Suppose the question gives the wire resistance as 4.0 ohms per 1,000 feet.
- Add up the current. 0.110 + 0.110 + 0.140 + 0.180 + 0.180 + 0.180 = 0.90 A.
- Convert resistance to per foot. 4.0 ohms ÷ 1,000 feet = 0.004 ohms per foot. Wire tables give ohms per 1,000 feet, so this step is almost always needed.
- Double the length. Current travels out on one conductor and back on the other, so 350 feet of run is 700 feet of wire.
- Find the resistance. 700 × 0.004 = 2.8 ohms.
- Apply V = IR. 0.90 A × 2.8 ohms = 2.52 volts of drop.
- End-of-line voltage, if asked: 24 − 2.52 = 21.48 volts.
This is the lump-sum approach CSA uses: all the load is treated as if it sits at the far end, which overstates the drop and so errs on the safe side. The most common wrong answer comes from skipping step 3. Using 350 feet instead of 700 gives 1.26 volts, exactly half the right answer, and it looks just as plausible on a multiple-choice list.
Two quick facts the guide tests directly: the smaller the AWG number, the larger the wire and the lower its resistance; and in code language, "shall" is the mandatory word.
A study plan
- Get NFPA 2001 (2018) and the NFPA 72 (2019) handbook, plus any NEC from 2008 to 2020, and print and bind CSA's study guide.
- Read NFPA 2001 with its annexes. Tab definitions, container requirements, design factors and the ITM chapter.
- Go through every NFPA 72 topic on the guide's list and find each one in your book. Tab the strobe tables, detector spacing and the ITM frequency tables.
- Tab NEC Articles 110, 300 and 760.
- Do voltage drop by hand until the six steps are automatic.
- Review OSHA lockout/tagout and fall protection without a book.
- Sit timed practice exams. At 90 seconds a question, you can't look up everything. See exam day.
CSA also links optional reading on its clean agent page that you can't bring in, including a voltage-drop research report called "V=IR" and System Sensor papers on notification appliances and duct detector testing. They help with understanding, but study the codes first.
Practice that matches the exam
Our CSA fire protection practice exams include a timed PEG2 exam with 80 questions, 2 hours and an 80% pass mark, written on the editions CSA lists, with a code reference on every answer. Try the free sample test, or read who needs PEG2.
Sources: CSA's Clean Agent Systems and Test Info pages and its Study and Test Material for the PEG2 Assessment (January 19, 2022), read November 2026. The voltage-drop example uses our own numbers to show the method in CSA's guide. CSA does not publish topic weights. The emphasis here is our reading of the study guide, not CSA's.
Ready to pass CSA Fire Protection Exams (KHFE2, FEX, CKH2, PEG2)?
Start your prep with unlimited practice tests and codebook-referenced answers.
Start Studying →

